@article { author = {Ghanbarzadeh, Jalil and Dashti, Hosin and Abbasi, Marzieh and Nakhaei, Mohammadreza}, title = {Torque Removal Evaluation of One-piece and Two-piece Abutment Screws under Dry and Wet Conditions}, journal = {Journal of Mashhad Dental School}, volume = {39}, number = {1}, pages = {89-98}, year = {2015}, publisher = {Mashhad University of Medical Sciences, School of Dentistry}, issn = {1560-9286}, eissn = {2008-2347}, doi = {10.22038/jmds.2014.3636}, abstract = {Introduction: Application of a lubricant material at the abutment screw interface has been proposed to reduce the possibility of screw loosening. The aim of this study was to compare removal torque values (RTVs) of one-piece and two-piece abutments tightened in three different conditions: dry, saliva impregnated and filled with saliva. Materials & Methods: 10 ITI implants were inserted in acrylic blocks. 10 one-piece abutments were connected on their corresponding implants and tightened with 10, 20 and 35 NCm torques. After each tightening, RTV of the abutment was measured. This experiment was conducted in three different conditions: dry environment, abutment screws impregnated with artificial saliva, and the fixture holes filled with artificial saliva. These procedures were repeated for two-piece abutments. Data were analyzed by repeated measure ANOVA and LSD tests. One-sample test was used to compare the RTVs with respective tightening torques (α=0.05). Results: The RTVs of one- piece and two piece abutments increased continuously when the environment changed from dry to impregnated and filled with saliva respectively (P<0.001). The RTVs of one-piece abutments were higher than those of two-piece abutments in three applied torques (P<0.001). Conclusion: The RTVs of both one-piece and two-piece abutments increased when the abutment screw was impregnated with artificial saliva and the fixture hole was filled with artificial saliva, respectively.}, keywords = {Dental implants,torque,lubricant}, title_fa = {بررسی گشتاور باز کردن پیچ اباتمنت‏های یک قطعه‏ ای و دو قطعه‏ ای در شرایط خشک و مرطوب}, abstract_fa = {مقدمه:استفاده از ماده لوبریکنت در حد فاصل رزوه‏های بین پیچ اباتمنت و ایمپلنت به منظور کاهش احتمال شل شدن پیچ اباتمنت پیشنهاد شده است. هدف از این مطالعه مقایسه گشتاور لازم برای بازکردن پیچ در اباتمنت‏های یک قطعه‏ای و دو قطعه‏ای در شرایط خشک و آغشته به بزاق و پر شده از بزاقبود. مواد و روش‏ها:10 ایمپلنت ITI در داخل بلوک‏های آکریلی مانت شد. 10 اباتمنت یک قطعه‏ای با نیروی گشتاور 10 و20 و 35 نیوتن سانتیمتر بر روی ایمپلنت‏های مربوطه محکم شدند و نیروی لازم برای باز کردن آنها ثبت شد. این آزمایش در سه شرایط مختلف انجام شد: محیط خشک، آغشته کردن پیچ اباتمنت به بزاق مصنوعی و پر کردن حفره فیکسچر با بزاق مصنوعی. همین مراحل برای اباتمنت‏های دو قطعه‏ای نیز تکرار شد. نتایج توسط آزمون Repeated measure ANOVA و LSD آنالیز شدند. برای مقایسه گشتاور باز کردن اباتمنت‏ها با گشتاور‏های بستن مربوطه از آزمون One-Sample t-test استفاده شد (05/0 (α=. یافته ‏ها:از محیط خشک به محیط آغشته به بزاق و محیط پر شده از بزاق میانگین گشتاور باز کردن اباتمنت‏های یک قطعه‏ای و دو قطعه‏ای به تدریج و به طور معنی‏داری افزایش یافت (001/0P<). هنگام استفاده از هر سه گشتاور بستن Ncm 10، 20 و 35 میانگین گشتاور لازم برای باز کردن، برای اباتمنت‏های یک قطعه‏ای بیشتر از دو قطعه‏ای بود (001/0P<). نتیجه گیری: در اباتمنت‏های یک قطعه‏ای و دو قطعه‏ای، به ترتیب آغشته شدن پیچ اباتمنت با بزاق و پرشدن حفره داخلی فیکسچر با بزاق گشتاور لازم برای باز کردن پیچ اباتمنت را افزایش می‏‎دهد.}, keywords_fa = {ایمپلنت دندانی,گشتاور بستن,پیچ اباتمنت,لوبریکنت}, url = {https://jmds.mums.ac.ir/article_3636.html}, eprint = {https://jmds.mums.ac.ir/article_3636_5f4bace1a23a4e9e1ea15f7122bb1969.pdf} }