@article { author = {Rezaei Rokni, Shahin and Moazzami, SayedMostafa and Hamedi Rad, Fahimeh}, title = {An In Vitro Evaluation on Shear Bond Strength of Three Resin Luting Cement Systems in Bonding of Base Metal Alloy and Ceramco and Inceram Porcelains to Dentin}, journal = {Journal of Mashhad Dental School}, volume = {31}, number = {شماره 1,2}, pages = {47-54}, year = {2007}, publisher = {Mashhad University of Medical Sciences, School of Dentistry}, issn = {1560-9286}, eissn = {2008-2347}, doi = {10.22038/jmds.2007.1402}, abstract = {Introduction:Developed synthetic resin cement are recommended for cementation of crown and bridges. Bonding of adhensive resins to ceramic, metal, enamel and dentin is an important factor for a successful clinical restoration. The purpose of this study was to determine the shear bond strength of 3 luting cement systems (Dual cure, self Cure and resin modified glass inomer) for bonding the base metal alloy, Ceramco and Inceram porcelain to dentin. Materials & Methods:In this experimental study, 90 extracted human teeth were prepared and buried in self cure acrylic resin while the buccal surface remained out of the acrylic material. The enamel of the buccal surface were removed and a flat surface was obtained on the dentin. Thirty blocks of base metal alloy, Ceramco laminate porcelain and Inceram were prepared with the dimensions of 6x4x2mm, and divided into 3 subgroups. Each subgroup was cemented with C & B Metabond, Panavia F and Rely X to dentin. After that, they were thermocycled between 5oc to 50oc for 500 cycles, the shear bond strengths were measured in an universal testing machine.  Finally, the specimens were inspected under a stereomicroscope with a magnification of 40 to determine the modes of failure. The data were analysed using SPSS software (2-way ANOVA, Duncan's test and Fisher's Exact test). Results:Maximum shear bond strength in bonding of 3 experimental plates to dentin with 3 adhesive resin systems are as follows: Panavia F for base metal plates (15.316±2.925 MPa), C&B Metabond for Ceramco porcelains (11.789±1.730 MPa) and Inceram porcelains (10.512±3.249 MPa). Conclusion:Within the limitation of this study, the best cement for cementation of base metal  plates was Panavia F or C & B Metabond cement. Among these three evaluated cements,C&B Metabond cement proved to be better for cementation of Ceramco porcelains to dentin and C&B Metabond or Panavia F for cementation of Inceram plates to dentin.}, keywords = {Resin cement,Shear bond strength,metal bonding,dentinal bonding,porcelain bonding}, title_fa = {بررسی آزمایشگاهی استحکام پیوند برشی سه سیستم چسباننده رزینی در اتصال فلز Base، پرسلن Ceramco و پرسلن Inceram به عاج دندان}, abstract_fa = {مقدمه: سمان های رزینی تکامل یافته برای سمان کردن بریج ها و کراون ها توصیه می شوند و میزان باند این سمان ها به فلز، پرسلن، عاج و مینا در موفقیت کلینیکی رستوریشن نقش مهمی دارد.هدف از این مطالعه تعیین سمان رزینی مناسب از نظر استحکام پیوند برشی برای باند آلیاژBase Metal، پرسلن Ceramco و پرسلن Inceram به عاج دندان از بین سه سمان رزینی با سه مکانیسم باند متفاوت Panavia F، C&B MetabondوRely X می باشد. مواد و روش ها: دراین مطالعه آزمایشگاهی مداخله گر، تعداد 90 دندان اینسایزور کشیده شدة انسان تهیه و مینای سطح باکال آنها تراشیده شد بطوری که سطحی صاف در عاج ایجاد گردید. سپس 30 صفحه از آلیاژ Base Metal، 30 صفحه از پرسلن Inceram و 30 صفحه از پرسلن Laminate کارخانه Ceramco به ابعاد mm6×4×2 تهیه و به سه زیر گروه تقسیم شدند.هر زیر گروه توسط سمانهای C&B Metabond، Rely X و  Panavia Fبر طبق دستور کارخانه سازنده به سطح آماده شدة دندان باند شدند. پس از اعمال 500 سیکل حرارتی، استحکام باند برشی نمونه ها توسط دستگاه تست یونیورسال بر حسب MPa تعیین شد. سپس نمونه ها از نظر محل وقوع شکست توسط استرئومایکروسکوپ با بزرگنمایی40  بررسی شدند. تحلیل آماری استحکام پیوند برشی با استفاده از نرم افزار آماری SPSS و آزمونهای واریانس دو عاملی، فیشر و دانکن انجام گردید. یافته ها: حداکثر استحکام پیوند برشی در اتصال سه نوع صفحه مورد آزمایش به عاج دندان به تفکیک سمان رزینی بترتیب ذیل بود: سمان Panavia F برای صفحات فلزی (MPa925/2±316/15)، سمان C&B Metabond برای صفحات پرسلنی Ceramco (MPa 730/1±789/11) و صفحات پرسلنی Inceram  (MPa249/3±512/10). نتیجه گیری: در محدودة ‌مطالعه فوق بهترین سمان برای سمان کردن صفحات از جنس فلزBase  به عاج دندان، سمان Panavia F یا C&B Metabond می باشد، برای سمان کردن صفحات پرسلن Ceramco به عاج دندان، سمان C&B Metabond و برای صفحات پرسلن Inceram به عاج دندان، سمانC&B Metabond  یا Panavia F است.}, keywords_fa = {سمان رزینی,استحکام پیوند برشی,باند به فلز,باند به عاج,باند به پرسلن}, url = {https://jmds.mums.ac.ir/article_1402.html}, eprint = {https://jmds.mums.ac.ir/article_1402_31515c2034a50645f695dc91c42914c3.pdf} }