@article { author = {Rezaee Soufi, Loghman and Kasraee, Shahin and Ghannadan, Kiana}, title = {The Effect of Er:YAG and Nd:YAG Lasers on Microtensile Bond Strength of a Sixth-Generation Two-Step Adhesive}, journal = {Journal of Mashhad Dental School}, volume = {40}, number = {4}, pages = {335-344}, year = {2016}, publisher = {Mashhad University of Medical Sciences, School of Dentistry}, issn = {1560-9286}, eissn = {2008-2347}, doi = {10.22038/jmds.2016.7236}, abstract = {Introduction: Previous studies have revealed the effectiveness of laser therapy in the improvement of dentin bonding. In other words, laser radiation can result in the higher bond strength of adhesives. Accordingly, the aim of this study was to propose an appropriate protocol for the use of Er:YAG and Nd:YAG lasers with the purpose of improving the bond strength of a sixth-generation two-step adhesive. Materials & Methods: In this experimental study, a total of 70 healthy extracted teeth were selected and classified into seven groups. The control group was prepared according to the manufacturer's instructions. The remaining six groups were treated with Er:YAG and Nd:YAG lasers before primer application (Er-BP and Nd-BP groups), after primer application (Er-AP and Nd-AP groups), and after bonding (Er-AB and Nd-AB groups). The specimens were covered with Filtek Z-250 resin composite (shade A2 and height of 4 mm), using an incremental technique and were then treated. Following that, the microtensile test was performed on the samples. The gathered data were analyzed, using one-way analysis of variance (ANOVA), followed by post-hoc Dunnett T3 test. P-value less than 0.05 were considered statistically significant. Results:The mean and standard deviation of bond strength in the groups were as follows: Control= 30.09±4.21, Er-BP= 18.83±4.21, Er-AP= 14.43±3.12, Er-AB= 19.67±4.96, Nd-BP= 20.35±5.55, Nd-AP= 39.85±4.13, and Nd-AB= 18.16±3.36. The values obtained in the Nd-AP group were significantly higher than the control group (P<0.05). However, the values reported in other groups were significantly lower in comparison with the control group (P<0.05). Conclusion:In the present study, use of Nd:YAG laser system after primer application (Nd-Ap) significantly improved the bond strength in comparison with the control group.}, keywords = {Adhesive,Bond Strength,Nd:YAG,Er:YAG}, title_fa = {اثر لیزرهای Er:YAG و Nd:YAG بر روی استحکام باند میکروتنسایل یک نوع ادهزیو نسل 6 دو مرحله‌ای}, abstract_fa = {مقدمه:مطالعات نشان داده اند تابش لیزر می تواند منجر به استحکام باند قوی‏تر سیستم ادهزیو ‌شود. لذا هدف از این مطالعه به دست آوردن یک پروتکل مناسب جهت کاربرد لیزرهای  Er:YAGو Nd:YAG به منظور بهبود استحکام باند در طی کاربرد یک نوع ادهزیو نسل 6 دو مرحله‌ای بود. مواد و روش ها:در این مطالعه تجربی، تعداد 70 دندان سالم کشیده شده انتخاب و به 7 گروه مساوی تقسیم گردید.  گروه کنترل(c)  مطابق دستورالعمل کارخانه آماده سازی شد و در 6 گروه دیگر از دو لیزر  Er:YAG (Er)و Nd:YAG (Nd) در مرحله قبل از اعمال پرایمر (Er-BP,Nd-BP)، بعد از اعمال پرایمر (Er-AP,Nd-AP) و بعد از اعمال باندینگ (Er-AB,Nd-AB) استفاده شد. نمونه ها توسط رزین کامپوزیت FiltekZ-250 با رنگ A2 با ارتفاع 4 میلی متر با تکنیک لایه لایه پوشانده و کیور شدند. نمونه ها تحت تست میکروتنسایل قرار گرفت و داده ها از طریق تست ANOVA یک طرفه و آزمون تکمیلی Tukey با سطح معنی داری 05/0 مورد آنالیز آماری قرار گرفت. (05/0α=) یافته ها:نتایج میانگین و انحراف معیار استحکام باند گروه‏ها 21/4±09/30C=، 21/4±83/18Er-BP=، 12/3±43/14Er-AP=، 96/4±67/19Er-AB=، 55/5±35/20Nd-BP=، 13/4±85/39Nd-AP=، 36/3±16/18Nd-AB= (مگاپاسکال) به دست آمد که در گروه Nd-AP (MPa) نتایج به طور معنی داری (05/0P<)بیشتر از گروه کنترل بود. استحکام باند در سایر گروه ها به طور معنی داری (05/0>P)  از گروه کنترل کمتر بود. نتیجه گیری:این تحقیق نشان داد که استفاده از لیزر Nd:YAG بعد از اعمال پرایمر (Nd-AP) باعث افزایش استحکام باند نسبت به گروه کنترل می‌شود. }, keywords_fa = {ادهزیو,استحکام باند,Nd:YAG,Er:YAG}, url = {https://jmds.mums.ac.ir/article_7236.html}, eprint = {https://jmds.mums.ac.ir/article_7236_5ccae8b54a238a1502f7dc9d38cadd16.pdf} }