@article { author = {Jahanbin, Arezoo and Shahabi, Mostafa and Mokhber, Nima and TavakkolianArdakani, Elham}, title = {Comparison of Nickel Ion Release and Corrosion Sites among Commonly Used Stainless Steel Brackets in Iran}, journal = {Journal of Mashhad Dental School}, volume = {33}, number = {1}, pages = {17-24}, year = {2009}, publisher = {Mashhad University of Medical Sciences, School of Dentistry}, issn = {1560-9286}, eissn = {2008-2347}, doi = {10.22038/jmds.2009.1287}, abstract = {Introduction: One of the characteristics of brackets is resistance to corrosion. Corrosion could disturb dental movement through increasing, the friction between arch wire and slot. It could also cause dental discoloration. The aim of this study was to compare corrosion rate as well as corrosion site of five commonly used brackets in Iran. Materials & Methods: In this in vitro experimental study, 80 lower central stainless steel brackets (18- slot) from different companies (Mira, Dentaurum, Forte, Joli and 3M) were selected. At first, the brackets were mounted in Rapid impression material and the photographs were taken from six different views for assessing slots, bases, and wings using stereomicroscope device with X50 magnification. Then, each 8 brackets were put into a capped glass containing artificial saliva with PH=7.2 and they were incubated in 37±1°c temperature. The amount of released Nickel ion was measured by Atomic absorption technique after 6 weeks and for each bracket, photographs were taken again from previous views. Statistical analysis was done using Chi-square, Cochrane and Kruskal-Wallis and McNimar tests. Results: The minimum Nickel ion release belonged to 3M brackets (0.86±0.1 PPB) and the maximum release was for Forte brackets (17.49±0.01 PPB). Furthermore, corrosion was seen more in bracket bases (mesh surfaces) and it was less observed in their faces. Conclusion: The order of the Nickel ion release was: 3M>Dentaurum> Joli> Mira>Forte. Corrosion was the highest in the base of the brackets.}, keywords = {Nickel,Corrosion,bracket}, title_fa = {مقایسه میزان آزاد سازی یون نیکل و محل ایجاد خوردگی در چند نوع براکت استینلس استیل رایج در بازار ایران}, abstract_fa = {مقدمه:یکی از ویژگی های مهم براکت، مقاومت به خوردگی است که خود خوردگی می تواند باعث اختلال در حرکت دندانها از طریق افزایش اصطکاک بین آرچ وایر و اسلات و نیز بروز تغییر رنگ در مینای دندانها گردد. هدف از این مطالعه مقایسه میزان خوردگی 5 نوع براکت رایج در بازار ایران و بررسی محلهای شایع ایجاد خوردگی در آنها بود. مواد و روش ها: در این تحقیق تجربی-آزمایشگاهی، 80 عدد براکت 018/0 استیل استاندارد اج وایز دندان سانترال پایین از کارخانه های Mira، Dentaurum، Forte، Joli و 3M (از هر کدام 16 عدد) انتخاب شدند. در ابتدا براکت‌ها در مادۀ قالب گیری Rapid مانت شده و از شش جهت با دستگاه استرئومیکروسکوپ با بزرگنمایی 50 از آنها عکس تهیه گردید. سپس براکت های مربوط به هر کارخانه به صورت 8 تا 8تا در ظروف شیشه‌ای   دربسته در محیط بزاق مصنوعی با 2/7=PH و در محیط انکوباتور تحت درجه حرارت 1±37درجه سانتی گراد  قرار گرفتند. پس از 6 هفته غلظت یون نیکل آزاد شده از هر نمونه به کمک روش جذب اتمی (Atomic absorption) اندازه‌گیری و مجدداً از هر براکت با کمک استرئومیکروسکوپ برای رویت مناطق خوردگی در جهات قبلی عکس تهیه شد. تجزیه و تحلیل آماری با آزمون های Chi-square، کوکران و کروسکال- والیس و مک نمار انجام گرفت. یافته ها: کمترین میزان آزادسازی نیکل مربوط به براکت 3M (PPB1/0±86/0) و بیشترین آن مربوط به براکت Forte (PPB01/0±49/17) بود. به علاوه سطح مش بیشترین و سطحی که بیس و بالچه از روبرو دیده می شدند از کمترین میزان خوردگی در کل براکت ها برخوردار بود. نتیجه‌گیری: ترتیب آزادسازی نیکل به صورت  3MJoli